Weld seam inspection · 100% inline
Hundreds of weld seams per component. One pass.
One station.
Multisensor inspection for large-area welded assemblies — geometry, completeness, surface and the finest defects are captured simultaneously, instead of serially in three inspection stations.
The challenge
Manual visual inspection does not scale. Pressure and X-ray testing take too long.
Anyone who has to inspect hundreds of weld seams per component usually has three bad options today: sampling — and accepting field complaints. Complete visual inspection — and bringing throughput to its knees. Pressure or X-ray testing — expensive, slow and informative only for certain defect classes.
What is missing is an inline inspection that captures geometry, completeness and the finest surface defects simultaneously — and at a pace that does not slow the line down.
That is exactly what we build.
If this applies to you
- Throughput is no longer sufficient — manual visual inspection slows the line.
- Field complaints because defects are only noticed at the OEM.
- Audit pressure (IATF, Pressure Equipment Directive, H₂ safety) demands complete documentation.
- Sampling lets too many defects through — the customer demands 100% proof.
- X-ray/CT inspection is too slow for the line cycle.
What the system does differently
Multisensor technology in one station.
Three sensor worlds, one pass, one inspection report. Geometry, completeness and the finest surface defects in the same scan — not three stations in sequence.
01 · Sensors combined
2D + 3D + AI in one setup
Area-scan cameras for the surface. Laser triangulation or fringe projection for the 3D geometry. Deep learning classification for defect assessment. Special illumination — dome, bright field, dark field, polarized — depending on the defect type. All in one station, instead of three in sequence.
Area-scan camera · Laser triangulation · Deep learning
02 · High speed
High speed on large components
Path speed approx. 200 mm/s for 3D inspection, depending on sampling rate and resolution. In 2D mode even up to 1,000 mm/s. Components up to approx. 2 m × 1.4 m flat. Resolution adapted to the application — down to micropores and hairline cracks.
up to 2 m × 1.4 m · 200 mm / s
03 · Multi-defect
Multiple defects and component features in one pass
Pores, cracks, geometry deviations, weld seam completeness plus further component features in one scan. No separate stations for visual inspection, geometry and leak testing.
Pores · Cracks · Geometry · Completeness
Fields of application
Where our systems are in use.
Our systems are already in use today in a variety of industrial fields. Three areas in which multisensor weld seam inspection is particularly in demand today:
Battery cases (e-mobility)
Laser weld seams on housings and module carriers, often dozens to hundreds per component. Requirement: reliably detect leak-relevant defects and geometry deviations without extending the cycle time.
Pressure vessels, tanks, piping construction
Weld seams on pressure-bearing components are subject to the Pressure Equipment Directive and audit obligations. Requirement: complete inspection documentation per seam, instead of sample-based visual inspection.
Hydrogen / electrolysis components
Stack components, bipolar plates, half-shells — the finest defects and micropores must be reliably detected in H₂ applications, because leakage is safety-relevant here.
Specifications & reference
What the system delivers technically.
Six values that describe the basic profile of the system. Concrete specification per application after a trial inspection.
- Component areaup to approx. 2 m × 1.4 m flat
- Path speed 2Dup to approx. 1,000 mm / s
- Path speed 3Dup to approx. 200 mm / s
- 2D resolutionsub-pixel accurate
- 3D height measurementµm range
- Detectable defectsdown to micropores & hairline cracks
- Sensors2D + 3D + AI + special illumination
“A MABRI.VISION system has been inspecting large-area welded assemblies in production since 2025 at a European industrial customer — multi-defect detection and completeness inspection in one pass.”
Anonymized reference · as of May 2026
MV.BRIX — modular platform
Configure instead of redeveloping
Our MV.BRIX platform consists of proven hardware and software modules — Automation, Vision, Software, Inspection. We configure your tailor-made system from these building blocks. Lower risk. Shorter lead times. Lower total cost of ownership.
- Scalable · maintainable · future-proof
- 100% tailored to your requirement
- Time-to-First-Measurement 6–8 months
From component to inspection report — in four steps.
A typical process when we jointly check whether your application is suitable for our system. Concrete time frames depend on the inspection scope and our workload and are agreed with you directly.
Inquiry & confidentiality
You describe the component, welding process and inspection task — under NDA if necessary. Together we discuss which defect classes we can realistically detect and which components are suitable for a trial measurement.
Sensor selection & inspection setup
Based on your component geometry and the relevant defect classes, we propose a suitable sensor combination (2D + 3D + illumination) and plan the inspection setup.
Measurement & evaluation
As soon as we have your components, we scan them in our technical center, classify the defects and agree intermediate results with you. If needed, we take additional measurements.
Inspection report & recommendation
You receive an inspection report with defect maps per seam, measurement data and our assessment of whether — and under which conditions — the application can reasonably be inspected with our system.
Who we are
From sensor to SAT —
from a single source.
MABRI.VISION has specialized in building optical inspection and measurement systems since 2015. We are around 50 employees in Aachen, with our own optics lab and cleanroom. Both managing directors are actively involved in every project — from feasibility to acceptance.
We do not sell components, and we do not sell off-the-shelf products. We build systems that work in the line, because the engineering team that designs them also stands behind them.
Inquire now
Send us your component. We will inspect it.
Request a trial inspection now. With your own components and a subsequent professional inspection report.
What can I expect?
- Sensor configuration — find out which technologies make sense for your application
- Cost estimate — find out early whether and when automated inspection pays off
- Anonymized pilot data from a trial measurement in the Aachen technology center
